HyBrid Clubs

You have seen these clubs used by top PGA Tour players while winning majors and other tour events world wide.  

If the best players in the world have taken their 2 and 3-irons out of their bags don't you think it is time you followed their lead?

 

 

MAKSER

AS 40 • Airflow Stabilizer Technology • "Roll and Bulge" face to optimize the transmission of energy to the ball • Utility Wood head in 17.4 steel • Dual Sole Inserts to lower center of gravity for optimum ball flight • Shaft fitted to your game.

 

WISHON GOLF TECHNOLOGIES

 

Head	Loft	Lie	Weight	Face Prog	Sole Angle	Bulge	Roll	Face Height	Face to Back	RH/LH
1-iron	15	57	224	7.0	0.0	20.0	0	35.0	51.0	RH
2-iron	18	58.0	231	7.0	0.0	20.0	0.0	35.0	51.0	RH/LH
3-iron	21	59.0	238	7.0	0.0	20.0	0.0	35.0	51.0	RH/LH
4-iron	24	59.5	245	7.0	0.0	20.0	0.0	35.0	51.0	RH
Assembly Length: GI-335 Graphite - #1(40.5"), #2(40"), #3(39.5"), #4(39");   Series 5 Steel - #1(40"), #2(39.5"), #3(39"), #4(38.5") Hosel Length: 52mm on all 321 Li hybrid ironheads Bore Depth: 30mm in all 321 ironheads;   Weight Bore in all 321 heads for final swing weighting Bore Diameter: 0.335" parallel;   Hosel O.D. - 12.3mm Ferrule Required: Yes. Choose wood ferrule with a 12.3mm bottom O.D. Scorelines: All U-groove scorelines, 0.8mm wide X 0.4mm deep X 4.5mm edge-to-edge spacing. Head Body Material: Investment cast from 17-4 Stainless Steel Head Construction: #1, 2, 3, 4 - 2-pc hollow body with custom wall thickness engineering Loft/Lie Bending: Only if the clubmaker uses a metal wood L/L bending machine;   Due to paint finish, some marring will occur Sole Radius Toe to Heel: 200mm (#1, 2, 3, 4) Sole Radius Face to Back: 200mm (#1, 2, 3, 4)
Features and Benefits
	* Model 321Li hybrid long iron replacements are finally the ultimate in true full hybrid long iron design due to the accompanying design of the matching GI-335 graphite iron shaft, or the Series 5 Steel .335" tip shaft.
	* TWGT research has shown that the shaft can be a major contributor to the launch angle of any club, but only if the shaft is designed to bend/deflect an amount much greater than is typical with a conventional iron shaft. Typical 0.370" tip diameter iron shafts only bend/deflect 1-2" in the swing. But 0.335" wood shafts bend/deflect 4-6" in the swing.The challenge of the GI335 and Series 5 Steel .335 shaft was to design them so that they had the same butt stiffness as a conventional iron shaft, but with a tip design that would not cause the shafts to feel too "whippy" when used with the heavier headweight of an iron.
	* 321Li full hybrid long iron heads are designed in a #1, 2, 3 and 4 iron and will match with any set of irons to offer the golfer a much higher trajectory from the bending of the unique .335" iron tip design of the GI-335 and Series 5 Steel shafts.
	* 321Li full hybrid long iron heads are designed with a hosel to face position that is much more like a true iron for the proper appearance and set up at address.
	* A cross-section view of the wall thickness of the 321Li head design shows another reason for the easy playability of this model - the rear wall of each 321Li is extremely thick to pull the CG farther back from the shaft to further assist with increasing the launch angle of the shot.
	* Ferrule of choice for the 321Li heads will be any .335 bore ferrule with a bottom O.D. of 12.3mm (any TWGT standard wood ferrule)
	* 321Li heads are designed with 0" roll just like and iron, but with a slight 20" horizontal bulge radius to match with the location of the CG farther back from the face than a typical ironhead.
	* 321Li full hybrid long iron heads are finished in an attractive dark grey metallic with bright satin highlights on the sole and toe/heel.